Designfax weekly eMagazine

Subscribe Today!

Archives

View Archives

Partners

Manufacturing Center
Product Spotlight

Modern Applications News
Metalworking Ideas For
Today's Job Shops

Tooling and Production
Strategies for large
metalworking plants

Engineer's Toolbox:
Using Teflon and other coating options to solve new engineering challenges

Teflon and other functional coatings from an experienced applicator can solve design problems such as excessive wear, sticking, noise, and corrosion.

Teflon, or polytetrafluoroethylene (PTFE), is one of the most versatile industrial coatings available today. Best known for its non-stick properties, it offers an extremely low coefficient of friction, chemical inertness, and excellent dielectric stability.

Because of ongoing advancements and more precise application techniques, the range of potential uses for PTFE (Teflon) and other functional coatings is greatly expanding.

 

 

While almost everyone has heard of Teflon, the expanding range of potential uses for PTFE and other functional coatings can often be overlooked. Ongoing advancements and more precise application techniques make them worth considering.

Far more than a coating for cookware, Teflon's non-stick properties can be used to solve a variety of design challenges, including preventing build-up of contaminants, corrosion, and bacteria; reducing friction or sticking between parts that come into contact; and even as an ingredient in heavy-wear, high-load applications.

"Teflon is the ultimate 'problem solver' for design issues that can include sticking, release, wear, noise, and abrasion," says George Osterhout of Orion Industries, one of the largest Chemours Licensed Applicators for Teflon coatings in North America. "Engineers often seek assistance when they are experiencing problems, whether it's a part that has no coating or a coating that isn't performing as expected."

According to Osterhout, there is no limit to the types of substrates that can be coated with Teflon. These include carbon steel, aluminum, stainless steel, steel alloys, brass, titanium, and magnesium, as well as glass, fiberglass, silicone rubber, rubber, and plastics.

There is also no limit to the kinds of products that are coated. A short list includes cookware, supercharger rotors, automotive throttle shafts, solenoids, airplane toilet bowls, the exterior of light bulbs, rubber O-rings, and the rollers used to cook hot dogs in convenience stores, to name a few.

Precision application
Today, the application of Teflon and other functional coatings has advanced into a precise, highly automated operation. Due to the investment in production equipment and the rigors of meeting environmental regulations, applicators of Teflon coatings are partnering with companies that previously performed this work in their own facility or that used to job it out to a local applicator.

However, within this group there can be a broad range of capabilities and levels of quality.

According to Osterhout, the difference in quality between applicators is usually defined by two primary factors: the proper and thorough pretreatment of parts prior to coating and the ability to apply a precise thickness of coatings as low as 10 microns with little to no variance between parts and at a tolerance of +/-3 microns. The industrial norm is 10 to 20 microns per side of coating.

To assure that level of precision, applicators must design and build their own production lines from the ground up. Furthermore, these systems must be configured to be flexible enough to accommodate a wide range of parts in different sizes and geometries.

As an example, Orion uses what they call a flexible cellular manufacturing approach to speed production for a wide variety of parts, while controlling the material cost and energy. The stationary equipment or robotic cell is moved into position and allows the coatings to be applied exactly to specification while using conveyers and ovens to do the flash and curing process or to completely cure the part. The parts are coated in these cells with very little overspray and coating waste.

"In our process, we meter out the coating material out of the gun so it is the same every single time," says Osterhout. "There is very little overspray, because we apply the coating where it needs to be, not all over the coating booth." By using infrared ovens mixed with convection air ovens, parts can often be cured three times fast than with traditional convection ovens only.

Non-stick for more than just food
Although Teflon is very popular as a highly durable and reliable coating for cookware, its non-stick qualities can be just as important for preventing the accumulation of foreign particles and contaminants and for its wear properties.

Teflon is the ultimate problem solver for design issues that can include sticking, release, wear, noise, and abrasion.

 

 

In many applications, the buildup of dirt, ice, soot, scale, food, and other foreign material can prevent the proper function of a machine or engine components. If contamination of a surface is anticipated, it can be minimized with thin Teflon coatings.

Teflon's non-stick properties make it an excellent corrosion barrier, as well. Coated parts can be used to prevent galvanic corrosion and shed corrosive fluids like salt water, process chemicals, fuels, and lubricants.

Today's formulations can also include anti-microbial agents that can benefit a wide range of applications.

Conformable coatings
For applications where very tight clearances between parts are required, such as rotary screw compressors, Teflon-based conformable coatings can be used to narrow the gap without allowing metal-to-metal contact during operation.

There are many benefits to decreasing the gap, including reducing noise, stopping air or fluid leakage, or creating a tighter hydrodynamic seal. In the case of rotary screw compressors, a conformable coating can increase efficiency over 10% or more without changing machining tolerances.

Ultra-thin conformable coatings, like the DB L-908 from Orion, for instance, contain a mixture of polyimide and other resins. The formulation contains nanometer-sized wear-resisting particles, as well as PTFE.

The coating is applied in thicknesses specified during initial design and testing, such that the two coated surfaces initially contact each other while allowing the tips clearance to pass in a rotary screw application.

Small air pockets in the polymer allow the coating to compress under mechanical pressure. Once compressed, the air pockets remain crushed so the coating holds the new profile. The PTFE in the formulation prevents the surfaces from galling or sticking to each other during this initial contact.

This is a superior alternative to surface hardening, which only delays galling, or more precise machining of parts with extremely tight tolerances.

Given the extremely tight clearance, these conformable coatings must hold +/-0.001-in. tolerance on all surfaces at a thickness of 0.002 in. to 0.006 in.

Low-friction coatings for silicone rubber
In addition to being a licensed applicator of Teflon coatings, some manufacturers have developed their own line of proprietary coatings. Case in point, Orion's FluoroBond LSR was designed to reduce the coefficient of friction of molded silicone rubber from 20% to 60%. In addition, it also aides in reducing the collection of dust or dirt on the finished coated surface.

Silicone rubber, though widely used for tubes, seals, and rollers, is tacky and can cling to any object it comes in contact with -- even other silicone surfaces. This is due to the material's high friction coefficient, which can exceed 1.0.

To lower the coefficient of friction on the surface of silicone parts, many applications use a Parylene coating that utilizes a chemical vapor deposition process to form a physical bond. However, Parylene is rigid, can crack, and also has no anti-microbial properties. Furthermore, only process parts that fit in the vapor chamber can be coated, and IDs (interior dimensions) are very difficult to coat.

FluoroBond LSR instead provides a chemical bond to silicone rubber to reduce the coefficient of friction. Due to its excellent elongation properties, the coating does not crack, and anti-microbial properties can be added.

Dry film lubricants
Typically, engineers are schooled in oil- or grease-based lubrication techniques, but not nearly as much time or attention is spent on dry film lubricants.

Unlike oil and grease that can migrate away, dry film lubricants continue to transfer back and forth on the mating surfaces and stay in place for a much longer time. Also, dry film coatings serve as a thin cushion, spreading high point loads in bearings and reducing element fatigue.

For this, graphite and molybdenum disulfide (Moly) are often used. Moly-disulfide coatings are recommended for conditions of heavy wear, particularly high-load situations. This includes bearing-type applications where one part rolls or slides over another part. Graphite coatings are generally used in wet service or at elevated temperatures.

Teflon can also serve as a dry film lubricant, though typically for light-to-moderate applications. Teflon is often incorporated with Moly and graphite into unique formulations.

R&D laboratory access
Osterhout admits that the variety of coating formulations, as well as the vast array of products that can potentially benefit users, can be daunting. In many cases, engineers have products with no coating, or a coating that isn't performing as expected, and need a resource to explore their options.

"Engineers need to establish how the Teflon coating is going to function, and they also need to know the thickness that will be applied to compensate for it to fit within their existing dimensions," says Osterhout.

To assist in developing specialized materials and application methods, a select number of applicators now maintain an in-house R&D laboratory to test new coatings available on the market and research and develop their own for specific customer applications.

Some labs are even equipped with the latest quality-control (QC) equipment for testing wear, lubrication, coefficients of friction, and other key application parameters. In addition, customers and prospects can consult with in-house engineering staff when custom coatings are required.

"We have access to baseline performance information from past research and experimentation, so we can compare one coating to another that we have developed," says Osterhout. "This allows us to know that we made substantial improvements in a new coating's performance."

Capabilities at Orion Industries include:

• Non-stick and industrial Teflon coatings
• Corrosion-resistant coatings
• Medical coatings
• Consumer/FDA coatings
• Anti-microbial coatings
• Dry film lubricants
• Chemical-resistant coatings
• Wear-resistant coatings
• Low-friction coatings for silicone rubber

Clients include: All-Clad, Baxter, Caterpillar Corporation, Chrysler, Calphalon Cookware, Whirlpool.

For more information, contact Orion Industries at (773) 282-9100, e-mail info@orioncoat.com or visit www.orioncoat.com.

Published August 2017

Rate this article